Underwire End Cover, Heat Shrink, 8 Tubular Piece Cut-To-Need
4.6 (228) · $ 1.99 · In stock
Underwire End Cover, Heat Shrink, 1~2" Tubular Piece Cut-To-Need, from Bra-Makers Supply is used to seal the sharp tip of any trimmed-to-size underwires. This product is sold in a ~8″ (30 cm) tubular piece, which is enough to cover several underwires. It is clear and thin enough to fit into the underwire casing. This H
Gigi's Bra Supply is the USA Distributor of Bra-Makers Supply, Canada aka braandcorsetsupply.com bra and corset supply, providing bra making supplies to bra makers, bra supplies for sewists, comfortable bra options with bra builder kits and bra sewing supplies
Underwire End Cover, Heat Shrink, 1~2 Tubular Piece Cut-To-Need, from Bra-Makers Supply is used to seal the sharp tip of any trimmed-to-size underwires.
This product is sold in a ~8″ (30 cm) tubular piece, which is enough to cover several underwires. It is clear and thin enough to fit into the underwire casing.
This Heat Shrink Underwire Cover is easy to apply with a heat gun and will properly seal the sharp end to keep it from poking through the underwire casing on bras, swimwear or foundation garments that require a slightly shorter underwire to fit into the casing.
Application:
To apply, cut a 1″ (or shorter) length of the Heat Shrink tube. Place it over the end of the underwire, allowing just a tiny bit of the Heat Shrink tube to sit beyond the end. Make sure you are working on a non-flammable surface and using proper gloves and eye protection. While holding one end of your underwire, heat the other end (with the Heat Shrink) with a heat gun until the Heat Shrink tube shrinks around the end. This will give you a nicely finished underwire that will not poke through your underwire casing in your bra, swimsuit top, or foundation garment.
Details:
Approximately 8″ (30 cm)
Underwire End Cover, Heat Shrink, 1~2 Tubular Piece Cut-To-Need, from Bra-Makers Supply is used to seal the sharp tip of any trimmed-to-size underwires.
This product is sold in a ~8″ (30 cm) tubular piece, which is enough to cover several underwires. It is clear and thin enough to fit into the underwire casing.
This Heat Shrink Underwire Cover is easy to apply with a heat gun and will properly seal the sharp end to keep it from poking through the underwire casing on bras, swimwear or foundation garments that require a slightly shorter underwire to fit into the casing.
Application:
To apply, cut a 1″ (or shorter) length of the Heat Shrink tube. Place it over the end of the underwire, allowing just a tiny bit of the Heat Shrink tube to sit beyond the end. Make sure you are working on a non-flammable surface and using proper gloves and eye protection. While holding one end of your underwire, heat the other end (with the Heat Shrink) with a heat gun until the Heat Shrink tube shrinks around the end. This will give you a nicely finished underwire that will not poke through your underwire casing in your bra, swimsuit top, or foundation garment.
Details:
Approximately 8″ (30 cm)
1-Count 19.05mm 6-in Heat Shrink Tubing
IDEAL 1-Count 19.05mm 6-in Heat Shrink Tubing
: Industrial & Scientific
MECCANIXITY Heat Shrink End Cap 20mm ID x 40mm L 2:1 Ratio Waterproof Electrical Wire Wrap Adhesive Lined Sealed Heat Shrink Tubing Caps for Wire
Lingerie Friday: Cutting & Tipping Underwires • Cloth Habit
Heat Shrink Tube - Dual Wall 1/8 - 6 inch Lengths
Another Way to Re-Tip Underwires
Heat Shrinkable End Caps, Insulating End Cap
Size: 2 | ID before Shrinking: 2.17 | ID after Shrinking: 1 2:1 Shrink Ratio - Shrinks to half its size Dual wall end cap, with internal wall of
2 Heat Shrink End Cap - 10 Pieces - Black
2 Heat Shrink End Cap - 10 Pieces - Black : Industrial & Scientific
Heat Shrinkable End Caps, Insulating End Cap
